top of page
Search

Twin-screw expander or turbine? Choosing the right ORC for your waste heat

joea92
6 minutes ago
3 min read

Every Organic Rankine Cycle (ORC) system has an expander at its heart: the machine that turns hot, high-pressure vapour into shaft power. There are two broad families. Turbo expanders (turbines) spin a bladed rotor at very high speed. Volumetric expanders, including the twin-screw expander in every ElectraTherm Power Module, trap the vapour in chambers that grow as two meshing rotors turn.

Neither is better across the board. A 2025 systematic review of ORC expander technology, published in Green Energy and Fuel Research, compares the two in detail. Its findings match what we see across the UK fleet: turbines suit big, steady heat sources, while twin-screw expanders suit the smaller, changeable heat that most UK sites actually have.

Where turbines shine

  • Peak efficiency. The review finds turbo expanders reach the highest isentropic efficiency, and suit high temperatures and high mass flows.

  • Big outputs. Radial turbines suit systems up to around 1,000 kW. Axial turbines are used above that, for example in commercial geothermal plants.

  • Steady heat. They perform best close to their design point, so they fit sources with a stable heat supply, such as geothermal wells and large incineration plants.

That performance comes at a price. Turbines run at tens of thousands of rpm, which demands precise bearings, seals and blade manufacture, and the review notes their design and manufacturing costs are high. Most also need a gearbox to drive a grid-frequency generator, which adds mechanical losses, vibration, noise and lubrication.

Where twin-screw expanders fit better

  • Heat that varies. Biomass boilers modulate, pyrolysis reactors cycle and engines change load. The review concludes that turbines have limited tolerance of these fluctuations and need complex controls such as variable guide vanes, while screw expanders offer more operational flexibility for small and medium systems with changing heat.

  • Smaller outputs. In a list of ORC installations in Taiwan from 2020 to 2025, included in the review, turbines were used mainly for geothermal and larger steam sites, while twin-screw systems were mainly used for industrial waste heat, mostly below 300 kW. ElectraTherm Power Modules are 75 kWe and 125 kWe.

  • Wet vapour. Volumetric expanders can handle two-phase flow, whereas liquid droplets striking turbine blades at high speed can shorten a turbine's life.

  • Lower speed, simpler drive. Screw expanders run at lower speeds and need less extreme precision, which keeps design and manufacturing simpler and cheaper. In an ElectraTherm Power Module, the twin-screw expander and induction generator share one sealed housing, with no gearbox.

The honest trade-off

Turbines win on peak efficiency at their design point, and the review is clear that screw expanders still face leakage and friction losses. But a turbine's peak figure only matters if your heat lets it run there. On a site where heat varies through the day and the season, what counts is the electricity generated over the year, and that's where an expander that holds its performance across a wide range earns its keep.

What this looks like in the UK fleet

Readings from the control screens of ElectraTherm units in the UK, taken in November 2026, show Power Modules running on hot water from 88 °C up to 138 °C, and expander-generators with over 34,000 run hours on the clock. See the UK fleet.

A quick rule of thumb

  • Consider a turbine for several hundred kW up to megawatts, from a steady, high-temperature heat source such as geothermal.

  • Consider a twin-screw ElectraTherm Power Module for tens to a few hundred kW, from heat that varies, such as hot water from biomass boilers, biochar and pyrolysis plants, engines and industrial processes.

On temperature: ElectraTherm Power Modules can technically run on hot water from 65 °C, but in our experience a project starts to make financial sense from around 80 °C. The PM75 runs on hot water up to 132 °C, and the 6500 up to 150 °C.

These are rules of thumb. We model every site with real fleet data before we quote.

Got waste heat?

Fill in our Request for Information form and send it to sales@koolbricks.co.uk, or get in touch. We'll show you what your heat could generate.

Reference

Hsieh, J.-C., Tsai, H.-T., Chen, Y.-T., Chen, C.-L. and Lin, C.-F. (2025). Volumetric and Turbine Expander Technologies in Organic Rankine Cycle Systems: A Systematic Review. Green Energy and Fuel Research, 2(3), 197–217. https://doi.org/10.53941/gefr.2025.100015

 
 
 

Comments


bottom of page